We bring to your attention a typical example of a job description for an equipment adjuster in production building materials, sample 2019. A person with primary or secondary vocational education, special training and work experience can be appointed to this position. Do not forget, each instruction of the equipment adjuster in the production of building materials is issued on hand against receipt.
It provides typical information about the knowledge that an equipment adjuster in the production of building materials should have. About duties, rights and responsibilities.
This material is included in the huge library of our site, which is updated daily.
1. General Provisions
1. An equipment adjuster in the production of building materials belongs to the category of workers.
2. A person with an average professional education or initial vocational education and special training and ____ years of work experience.
3. An equipment adjuster in the production of building materials is hired and dismissed by the director of the organization upon the presentation of _______.
4. The adjuster of equipment in the production of building materials must know:
a) special (professional) knowledge of the position:
- arrangement of pipe-cutting and pipe-turning machines for processing asbestos-cement pipes and couplings, rules for their adjustment;
- the device of hydraulic presses and the rules for their adjustment to different modes of pressing;
— standards ( specifications) for manufactured products;
- allowable tool wear dimensions;
— device and methods of adjustment of serviced equipment;
- rules for disassembly and assembly of all nodes of serviced mechanisms;
— lubrication system for serviced equipment; the device of the used working and measuring tool;
- rules of technical operation, electrical circuit of the serviced equipment and instrumentation;
- the service life of individual parts and the procedure for their replacement;
b) general knowledge of the employee of the organization:
— rules and norms of labor protection, safety measures, industrial sanitation and fire protection,
- rules for the use of funds personal protection;
- requirements for the quality of work (services) performed, for rational organization work in the workplace;
- types of marriage and ways to prevent and eliminate it;
- production signaling.
5. In its activities, the equipment adjuster in the production of building materials is guided by:
- the legislation of the Russian Federation,
— Charter of the organization,
- orders and directives organization director,
- this job description,
— Rules of internal work schedule organizations.
6. The equipment adjuster in the production of building materials reports directly to ___________ a worker with a higher qualification, the head of production (section, workshop) and the director of the organization
7. During the absence of the equipment adjuster in the production of building materials (business trip, vacation, illness, etc.), his duties are performed by a person appointed by the director of the organization on the proposal of ________ in in due course which acquires the corresponding rights, duties and is responsible for the fulfillment of the duties assigned to it.
2. Responsibilities of the equipment adjuster in the production of building materials
Job responsibilities of the equipment adjuster in the production of building materials are:
a) Special (professional) duties:
— Adjustment of semi-automatic pipe-cutting, coupling-cutting and pipe-turning machines.
— Change of the cutting tool and installation of rollers on pipe cutting machines.
– Adjustment of hydraulic presses with a capacity of up to 5000 tons for different pressing modes in relation to the requirements of pressed products and the technology of their production.
– Adjustment, regulation and ensuring the smooth operation of technological, power and transport equipment of quarries, drying, firing, clay and cement-sand tiles, expanded clay gravel, aggloporite, lime and gypsum and mass-preparation departments of sand-lime brick factories.
— Change of worn parts and units of mechanisms.
— Manufacture and replacement of small spare parts.
- Elimination of malfunctions in the operation of mechanisms.
— Lubrication of rubbing parts of mechanisms.
- Participation in the repair and acceptance of serviced equipment after repair.
- Keeping a log of equipment operation.
– Adjustment and maintenance of uninterrupted operation of unloading machines, transporting devices, crushing and screening, grinding and concrete mixing units, dosing devices and apparatus, harvesting and fitting equipment.
— Observation and control of the operation of mechanisms, adjustment and regulation of the mode of their operation.
- Preliminary preparation and replacement of worn parts and assemblies.
— Briefing service personnel maintenance and operation of the equipment.
– Adjustment and ensuring the smooth operation of pumps, circular saws, drilling machines and other similar equipment.
– Installation, tension and fastening of saws in the frame of stone sawing machines.
b) General duties of an employee of the organization:
— Compliance with the Internal Labor Regulations and other local regulations of the organization, internal rules and norms of labor protection, safety, industrial sanitation and fire protection.
— Execution within employment contract orders of employees to which it is repaired in accordance with this instruction.
– Performing work on the acceptance and delivery of shifts, cleaning and washing, disinfection of serviced equipment and communications, cleaning the workplace, fixtures, tools, as well as keeping them in good condition.
- Maintaining established technical documentation.
3. Rights of the equipment adjuster in the production of building materials
The equipment adjuster in the production of building materials has the right to:
1. Submit proposals for management consideration:
– to improve the work related to the provisions of this responsibilities,
— on bringing to material and disciplinary responsibility employees who violated production and labor discipline.
2. Request from structural divisions and employees of the organization the information necessary for him to fulfill his official duties.
3. Get acquainted with the documents that define his rights and obligations in his position, the criteria for assessing the quality of performance of official duties.
4. Get acquainted with the draft decisions of the organization's management regarding its activities.
5. Require the management of the organization to provide assistance, including the provision of organizational and technical conditions and execution of the established documents necessary for the performance of official duties.
6. Other rights established by the current labor law.
4. Responsibility of the equipment adjuster in the production of building materials
The equipment adjuster in the production of building materials is responsible in the following cases:
1. For improper performance or non-performance of their official duties provided for by this job description - within the limits established by labor legislation Russian Federation.
2. For offenses committed in the course of their activities - within the limits established by the current administrative, criminal and civil legislation of the Russian Federation.
3. For causing material damage organizations - within the limits established by the current labor and civil legislation of the Russian Federation.
Job description for an equipment adjuster in the production of building materials - a sample of 2019. The duties of the equipment adjuster in the production of building materials, the rights of the equipment adjuster in the production of building materials, the responsibility of the equipment adjuster in the production of building materials.
Real job description developed and approved in accordance with the provisions Labor Code Russian Federation, Unified Tariff and Qualification Handbook of Works and Professions of Workers, Issue 20, Part 1, Manufacture of products electronic engineering Chapter " General Professions production of electronic products”, approved by the Decree of the Ministry of Labor of the Russian Federation of January 21, 2000 N 5, and other regulatory legal acts regulating labor relations.
1. General Provisions
1.1. The adjuster of technological equipment of the 6th category belongs to the category of workers and directly reports to [name of the position of the immediate supervisor].
1.2. A person with a secondary specialized education and at least [value] years as a process equipment adjuster of the 5th category is accepted for the position of a technological equipment adjuster of the 6th category.
1.3. The adjuster of technological equipment of the 6th category must know:
- kinematic, electronic, optical and electrical circuits;
— vacuum and gas systems of complex equipment;
— design features and principle of operation of installations with program management;
- purpose, rules for setting up and regulating instrumentation of all systems;
- the causes of occurrence and measures to prevent malfunctions in the operation of the serviced equipment;
- a methodology for carrying out all types of repairs;
- calculations related to the choice of the operating mode of the equipment, the replacement of elements of circuits and mechanisms;
- requirements for the rational organization of labor in the workplace;
- Rules and norms of labor protection.
2. Job responsibilities
The adjuster of technological equipment of the 6th category is assigned the following job responsibilities:
2.1. Adjustment and regulation of complex equipment with automatic, software and mechanical control with complex kinematic, electrical, vacuum, gas and electronic circuits for the production of complex devices.
2.2. Repair and adjustment of complex installations for electron-beam, argon-arc and thermal diffusion welding.
2.3. Repair and adjustment of complex oil and oil-free vacuum systems.
2.4. Calculation and installation optimally allowable regimes equipment operation.
2.5. Determination of wear, adjustment and replacement of mechanical, vacuum and electronic components.
2.6. Calculation and manufacture of inductors.
2.7. Performing all types of repairs of serviced equipment.
2.8. Drawing up sketches for complex parts, assemblies and necessary equipment.
2.9. Modernization of serviced equipment when changing the technological process.
2.10. Checking repaired equipment, conducting climatic tests of special technological equipment in heat chambers at low and high temperatures.
2.11. Management of workers of lower ranks of the same profession.
2.12. Performing work on the acceptance and delivery of shifts, cleaning the workplace, fixtures, tools, as well as keeping them in proper condition.
2.13. Maintaining established technical documentation.
2.14. [Other Job Responsibilities].
3. Rights
The adjuster of technological equipment of the 6th category has the right to:
3.1. For all social guarantees provided for by law.
3.2. Make suggestions to senior management to improve their work.
3.3. Require the management of the organization to assist in the performance of its professional duties and exercise of rights.
3.4. Receive information and documents necessary for the performance of their duties.
3.5. Improve your professional qualifications.
3.6. [Other rights provided for by labor legislation].
4. Responsibility
The adjuster of technological equipment of the 6th category is responsible for:
4.1. For failure to perform or improper performance of their official duties provided for by this job description - within the limits determined by the current labor legislation of the Russian Federation.
4.2. For causing material damage to the employer - within the limits determined by the current labor and civil legislation of the Russian Federation.
4.3. For offenses committed in the course of carrying out their activities - within the limits determined by the current administrative, criminal, civil legislation of the Russian Federation.
The job description was developed in accordance with [name, number and date of the document]
Head of Human Resources
[initials, last name]
[signature]
[day month Year]
Agreed:
[job title]
[initials, last name]
[signature]
[day month Year]
Familiarized with the instructions:
[initials, last name]
[signature]
[day month Year]
Job description for the adjuster of technological equipment of the 6th category
This job description has been translated automatically. Please note that automatic translation does not provide 100% accuracy, so there may be minor translation errors in the text.
| Instructions for the position " Production equipment adjuster food products 4th category", presented on the site, complies with the requirements of the document - "DIRECTORY qualification characteristics occupations of workers. Issue 7. General professions of production workers Food Industry", which was approved by the resolution State Committee Ukraine on the food industry 19.02.1997. Approved by the Ministry of Labor of Ukraine, the Ministry Agriculture and Food of Ukraine, the Ministry of Fisheries of Ukraine. The status of the document is "valid". |
|
Preface to job description
0.1. The document comes into force from the moment of its approval.
0.2. Document developer: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _.
0.3. Document approved: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _.
0.4. Periodic check this document produced at intervals not exceeding 3 years.
1. General Provisions
1.1. The position "Adjuster of equipment in the production of food products of the 4th category" belongs to the category "Workers".
1.2. Qualifications- vocational education. Advanced training and work experience by profession as an equipment adjuster in the production of food products, 3rd category - at least 1 year.
1.3. Knows and applies:
- structure and design features of equipment and automatic machines;
- mode of operation of machines and units;
- causes of malfunctions in the operation of equipment, methods for their implementation and elimination;
- the order of disassembly, assembly and regulation;
- instructions for the operation and repair of equipment;
- norms of the stock of consumable parts;
- requirements for the quality of adjustment;
- necessary control and measuring instruments;
- tolerances on the dimensions of parts, methods for their verification.
1.4. An equipment adjuster in the production of food products of the 4th category is appointed to the position and dismissed from the position by order of the organization (enterprise / institution).
1.5. The equipment adjuster in the production of food products of the 4th category reports directly to _ _ _ _ _ _ _ _ _ _ .
1.6. The equipment adjuster in the production of food products of the 4th category manages the work of _ _ _ _ _ _ _ _ _ _ .
1.7. The equipment adjuster in the production of food products of the 4th category during the absence is replaced by a person appointed in the prescribed manner, who acquires the appropriate rights and is responsible for the proper performance of the duties assigned to him.
2. Description of work, tasks and job responsibilities
2.1. Establishes, adjusts and repairs semi-automatic and automatic lines under the guidance of a tuner over highly qualified and individual machines and machines.
2.2. Checks the status and correct interaction of all equipment nodes.
2.3. Warns, detects and eliminates technical malfunctions in the operation of equipment.
2.4. Performs replacement, adjustment and adjustment of wear parts and gaskets.
2.5. Carries out installation, balancing and testing of equipment.
2.6. Controls the operation of semi-automatic lines and individual automatic machines.
2.7. In the course of work adjusts and regulates knots and mechanisms.
2.8. Participates in various types of repair, testing and commissioning of equipment.
2.9. Makes requests for the necessary parts and materials.
2.10. Lubricates equipment, stuffs seals and stitches passes.
2.11. Knows, understands and applies the current regulatory documents relating to its activities.
2.12. Knows and complies with the requirements of normative acts on labor protection and environment, complies with the norms, methods and techniques for the safe performance of work.
3. Rights
3.1. The 4th category food production equipment adjuster has the right to take actions to prevent and eliminate the occurrence of any violations or inconsistencies.
3.2. The adjuster of equipment in the production of food products of the 4th category has the right to receive all social guarantees provided for by law.
3.3. The equipment adjuster in the production of food products of the 4th category has the right to demand assistance in the performance of his duties and the exercise of rights.
3.4. The equipment adjuster in the production of food products of the 4th category has the right to demand the creation of organizational and technical conditions necessary for the performance of official duties and the provision necessary equipment and inventory.
3.5. The adjuster of equipment in the production of food products of the 4th category has the right to get acquainted with the draft documents relating to his activities.
3.6. The adjuster of equipment in the production of food products of the 4th category has the right to request and receive documents, materials and information necessary for the performance of his duties and orders of the management.
3.7. An equipment adjuster in the production of food products of the 4th category has the right to improve his professional qualifications.
3.8. The equipment adjuster in the production of food products of the 4th category has the right to report all violations and inconsistencies identified in the course of its activities and make proposals for their elimination.
3.9. The adjuster of equipment in the production of food products of the 4th category has the right to get acquainted with the documents defining the rights and obligations of the position held, the criteria for assessing the quality of performance of official duties.
4. Responsibility
4.1. The equipment adjuster in the production of food products of the 4th category is responsible for non-fulfillment or untimely fulfillment of the duties assigned by this job description and (or) non-use of the rights granted.
4.2. The equipment adjuster in the production of food products of the 4th category is responsible for non-compliance with the rules of internal labor regulations, labor protection, safety, industrial sanitation and fire protection.
4.3. An equipment adjuster in the production of food products of the 4th category is responsible for disclosing information about an organization (enterprise / institution) that is a trade secret.
4.4. The equipment adjuster in the production of food products of the 4th category is responsible for non-fulfillment or improper fulfillment of the requirements of internal normative documents organizations (enterprises/institutions) and legal orders of management.
4.5. The adjuster of equipment in the production of food products of the 4th category is responsible for offenses committed in the course of its activities, within the limits established by the current administrative, criminal and civil legislation.
4.6. The equipment adjuster in the production of food products of the 4th category is responsible for causing material damage to the organization (enterprise / institution) within the limits established by the current administrative, criminal and civil legislation.
4.7. The equipment adjuster in the production of food products of the 4th category is responsible for the misuse of the granted official powers, as well as their use for personal purposes.
Unified Tariff and Qualification Directory of Works and Professions of Workers (ETKS), 2019
Issue №20 ETKS
The issue is approved by the Decree of the Ministry of Labor of the Russian Federation of January 21, 2000 N 5
(as amended by the Decree of the Ministry of Labor of the Russian Federation of September 12, 2001 N 67)
Test equipment installer
§ 48. Adjuster-installer of test equipment of the 3rd category
Job Description. Adjustment and regulation of simple radio-electronic units of test equipment. Installation of individual nodes, connections, devices and blocks of medium complexity according to the wiring diagram with complete termination of conductors and connections. Cutting multi-wire armored cables in a rubber sheath with termination of the ends in the blocks. Production of all kinds of harnesses from wires of various brands according to templates. Unsoldering of simple circuits of repaired devices with installation and soldering of replaceable parts and assemblies. Electrical and mechanical adjustment and regulation, verification and testing of electrical measuring equipment of medium complexity, as well as balancing of the mobile system of instruments. Regulation of the main power sources. Identification and elimination of mechanical and electrical faults during adjustment and testing. Identification of defects in mounted circuits and their elimination. Testing and ringing of mounted circuits with electrical measuring instruments, finding defects and their elimination. Test of resistance and insulation of conductors. Establishing the sequence of installation of circuits.
Must know: methods for determining faults; installation of simple radio-electronic units and operational installation of complex products with conductors of various sections; the principle of operation of mounted mechanisms and devices; symbols of devices and components in the wiring diagram in a general form; installation and circuit diagrams of medium complexity; basic information on electrical engineering of alternating and direct currents within the scope of the work performed; mechanical and electrical properties of conductors and insulating materials used during installation; the purpose and arrangement of measuring and electrical measuring instruments used to check the polarity, breaks and short circuits in the mounted circuit; methods for including mounted elements in the control and test network; methods of setting the applied measuring equipment; methods of mechanical and electrical adjustment of electrical measuring equipment of medium complexity; rules for using and connecting them to regulated instruments and devices; installation and soldering requirements.
Work examples
1. Power supplies for klystrons, pumping stations, test stand for measuring the electrical parameters of the TWT, pulse shaping amplifiers, etc. - installation, repair, adjustment.
2. Amplification unit of the magnetic induction meter - installation.
3. Capacitor blocks - tuning and electrical regulation.
4. Full-wave rectifiers - installation and testing.
5. Low-frequency generators GZ-3b, GZ-33, GCh-31 - replacement of lamps and semiconductor devices; finding and troubleshooting in the generator unit.
6. Sound generators - step-by-step electrical check and regulation.
7. Resistive-capacitive voltage divider for pulse signals of microsecond and millisecond duration - installation and configuration.
8. Measuring complexes based on computers - daily Maintenance.
9. Electromechanical meters - step-by-step regulation.
10. Power supplies of all types, sound generators, thermoionization vacuum gauges, tube voltmeters - repair and regulation.
11. Heat chambers DR-164 - setting the thermal regime; regulation of the fan drive unit; heater replacement.
12. Electrical measuring mechanisms of classes 1 - 2, 5 - balancing.
13. Non-standardized devices for measuring R, L, C - setting.
14. Oscilloscopes - simple repair, adjustment.
15. Test equipment for OS, fuel assemblies, power transformers and chokes - maintenance; elimination of minor faults and control of parameters.
16. Test equipment - checking electrical circuits, test connectors; repair of RSH type connectors.
17. Printed circuit boards (modules) - desoldering microcircuits, checking their functioning; identification of faulty elements and their replacement.
18. Electrical measuring instruments - verification with the connection of a reference stand; change of electrical measuring instruments; magnetization and remagnetization of magnets.
19. Thermoelectric system devices, power supplies of all types, sound generators, thermoionization vacuum gauges, tube voltmeters - repair and regulation.
20. Prefixes to the characterograph - installation and adjustment.
21. Potentiometer - installation.
22. Relay circuits of high-frequency transmitters - electrical regulation.
23. Special equipment - regulation of nodes and blocks.
24. Measuring stand locking system - check and installation.
25. Bridge circuits for measuring R, L, C - setting.
26. Test benches - assembly of individual units and blocks, verification, adjustment.
27. Pollution control unit UZK-1 - control setting and repair of electronic account.
28. Installation for measuring the volt - capacitance characteristics ZhKM 346.001 - adjustment and regulation of the comparator and threshold discriminator.
29. Installation of burning by periodic pulses - repair, adjustment.
30. Installation for testing static parameters - repair of cathode, grid and anode circuits.
31. Impulse magnetizing installation - adjustment.
32. Switching circuits - repair, preventive maintenance, replacement of relays, keys, toggle switches, installation equipment.
33. Electric motors - collector cleaning, lubrication, motor change; connection to the installation and running.
§ 49. Adjuster-installer of test equipment of the 4th category
Job Description. Adjustment and regulation of radio-electronic units of test equipment of medium complexity. Establishment of optimally permissible operating modes of equipment and monitoring their stability. Finding damage in interblock connections and elements of the microwave path of measuring stands. Installation of equipment of medium complexity according to the wiring diagram and simple experimental devices according to the concept diagram with the implementation of various assembly, termination and cable work. Making circuits for experimental devices and apparatuses from various conductors, cables, tires and testing them with various electrical measuring instruments. Unsoldering and sealing of devices, blocks, assemblies, circuits and production of circuit diagrams and wiring diagrams for knitting circuits. Drawing up wiring diagrams and artificial lines. Cutting and soldering of all kinds of conductors, cables and tires. Simple calculations of resistance in various links of the circuit, testing of resistance and insulation of conductors. Electrical and mechanical regulation, testing, verification of complex electrical measuring equipment. Identification of various problems during installation, finding places of damage and eliminating them by replacing nodes and parts of the circuit, followed by a test under current. Measurement of electrical characteristics in accordance with the control and measuring instructions.
Must know: methods for identifying typical malfunctions of test equipment and installation of radio-electronic equipment; assembly and circuit diagrams of group connections of devices and devices included in the assembly diagram; rules for connecting circuits, installing parts and devices, the sequence of their inclusion in the overall circuit; technological and electrical properties of various conductive and insulating materials used during installation; principle of operation and purpose of control and measuring and auxiliary equipment (avometer, generators, voltmeters, oscilloscope, etc.); purpose and use of the mounting tool; power supply connection diagram when assembling circuits; fundamentals of electrical engineering, radio engineering, impulse technology; device and principle of operation of the tested circuit; methods for testing micromodules using maps of resistance, voltage, and electrical parameters.
Work examples
1. Automatic machines (type U-701, U-705, U-706, UPS, PRS, GP-5) - regulation by electrical parameters.
2. Automatic measurement of statistic parameters 261.0061 - regulation of the unit for supplying diodes to contact pads; repair of threshold devices.
3. Automatic packaging machines for microcircuits in loading boards - repair and adjustment.
4. Automatic classification 2.650.050/09 - regulation of the mechanism for supplying devices to contacting devices; repair and adjustment of the measuring channel.
5. Ammeters, voltmeters - regulation and verification.
6. Glow power supply with voltage stabilization - assembly and testing.
7. Relay and control units - installation.
8. Control relay blocks for high-voltage rectifiers up to 50 W - installation and adjustment.
9. Scanners for testing cathode ray tubes - medium repair.
10. Lamp microammeter block - installation, adjustment.
11. Stationary dual-range quartz generators powered by rectifiers - electrical regulation.
12. Sawtooth voltage generator - setting.
13. Mode setters for integrated circuits and micromodules - installation, adjustment.
14. Pulse sensors, indicators and course graphs - regulation.
15. Frequency divider on logic elements or triggers of integral design - installation and configuration.
16. Power supplies built on the principle of using chokes with saturation - installation and commissioning.
17. Stabilized high-voltage power supplies - repair.
18. Climatic non-contact control chamber - adjustment and repair.
19. Heat chambers 12 KTS, KTS-M - repair and adjustment.
20. V6-1, V1-4 tube voltmeter calibrators and V3-24 type tube voltmeters - repair and adjustment of the alternating voltage generator unit.
21. Thermal cycling chambers KTC-0.025 - setting temperature conditions and repairing the electrical circuit.
22. Semi-automatic coercimeter - setting.
23. Ruler for assembling and adjusting reversible periodic systems - setting.
24. Mechanisms of time, software, arresting - regulation.
25. Equipment for tuning semiconductor devices - adjustment and regulation.
26. Mounting and welding equipment (relay blocks, resistance boxes, current regulators and starting devices) - adjustment.
27. Equipment for ETT, including USTT - 0.25 s. thermotracers 1609 - repair, adjustment.
28. Electronics-100 printed circuit boards, alarm register, analog signal converter, switching register, indication blocks, fixing switching levels, logarithmic current converter, sweep generator - simple repair, regulation, adjustment, installation.
29. Devices of the magnetoelectric system of class 0.2 - 1.5, combined devices of the type "C" and "TT", bridges and resistance boxes, amplifiers general purpose- repair, adjustment, alignment.
30. High frequency switches various kinds, waveguide and coaxial couplers, thermistor heads and ballometers - testing and adjustment.
31. Measuring receiver - repair.
32. Devices with a Hall sensor - installation and adjustment.
33. Measuring systems such as digital voltmeter, digital printer, perforator, comparator and code converter - installation and configuration.
34. Systems for automatic temperature maintenance of furnaces - repair and adjustment.
35. Electronic stabilizers of direct and alternating current with a power of up to 300 W - installation, adjustment, repair.
36. Stand for carrying out climatic and mechanical tests, stands for current training - repair and adjustment.
37. Stand for setting modes UNTM / D - checking the sources of the right current and reverse voltage; setting the temperature setting block; bringing the stand to thermal and electrical modes.
38. Stand for panoramic measurement of TWT parameters - repair.
39. Test benches for group testing of OS, TVS, line-scan tube circuits - adjustment, troubleshooting, parameter control.
40. Schemes of simple stabilized power supplies - manufacturing, regulation.
41. Schemes for measuring static parameters, reverse currents - adjustment, repair.
42. Schemes for testing micromodules at extreme temperatures (+70 degrees C and -40 degrees C) - assembly, repair, adjustment.
43. Trigger circuits - adjustment.
44. Thyristor voltage regulators - repair.
45. Installations for measuring reverse currents - repair, adjustment.
46. Installations for measuring the parameters of semiconductor devices, testing transistors for heat and cold resistance, thermal cycling installations - adjustment, repair.
47. Installation for testing semiconductor devices at elevated and reduced pressure - preventive maintenance, adjustment.
48. Installation for testing the wettability of the leads of semiconductor devices with solder POS-40, POS-60 - adjustment, preventive maintenance.
49. Installations for tightness control "dry method" UKGE - repair, adjustment.
50. Vibrating, shock, mounting installations - repair, adjustment.
51. TTL-490 switching charge measurement settings - calibration setting by reference capacities and regulation of a long pulse edge.
52. Installations for measuring the resistance of the detector at the zero point, capacitance, quality factor - repair, adjustment.
53. Characterograph - adjustment.
54. Digital measuring instruments such as Shch4312, ChZ-30, "I2-19, ChZ-24 - identifying and eliminating faults in one of the blocks of counting decades; checking the circuit of logical operations.
55. Electric generator type ZGDA - installation and adjustment.
§ 50. Adjuster-installer of test equipment of the 5th category
Job Description. Adjustment and regulation of radio-electronic units of test equipment and computers of increased complexity. Adjustment of equipment for partial testing of color kinescopes. Installation of large groups of varying complexity of radio-electronic devices, instruments and apparatuses included in the overall wiring diagram. Installation of experimental samples according to sketches and schematic diagrams. Production without samples of circuits from various conductors, cables, tires and radio components. Testing circuits with various electrical measuring instruments. Production according to circuit diagrams and wiring diagrams of templates for knitting circuits with compact placement of conductors and in compliance with technical requirements by setting them up. Drafting of schematic diagrams based on product samples. Drawing up wiring diagrams and artificial lines. Calculations of resistance in various links of the circuit, testing of resistance and insulation of conductors. Electrical and mechanical regulation, verification, testing of complex electrical equipment. Regulation of switch instruments and devices of various systems and degrees of accuracy. Software troubleshooting on test and measuring equipment. Production, adjustment of individual boards for radio-electronic devices to replace those that have become unusable. Run control programs during commissioning of measuring equipment. Control tests and delivery of radio-electronic units with a demonstration of the operation of devices and entire installations according to the general scheme during commissioning. Preventive work on test and measuring equipment.
Must know: methods for identifying various malfunctions and methods for installing complex radio-electronic installations, measuring equipment and objects with a large number of incoming devices and devices with independent circuits; all kinds of assembly and schematic diagrams of group connections of devices and devices; the appointment of individual devices, units included in the mounted circuit; the principle of operation of various devices and radio tubes included in the mounted circuit; test methods for group connections of devices and devices mounted in a common circuit; rules for setting up and adjusting various radio measuring devices, testing and measuring equipment, the procedure and sequence for laying the installation; purpose and rules for shielding conductors and individual links; fundamentals of electrical engineering, radio engineering and impulse technology; rules for setting up and regulating various electrical measuring instruments.
Work examples
1. Units for measuring the electrical parameters of devices - repair, adjustment, performance check.
2. Akulov anisometer - setting.
3. Automatic machines with complex kinematic and electrical circuits - adjustment and repair.
4. Computer and stationary equipment - regulation of nodes and blocks.
5. Blocks with electromagnetic, eccentric mechanisms - regulation.
6. Non-contact regulation blocks on thyristor circuits, control and power blocks for reliability testing, logic blocks - adjustment, repair, installation.
7. Blocks of high-voltage stabilized power supplies - adjustment.
8. Stabilized rectifiers - setting and testing.
9. Vibrating stand VU 10/3000 - setting up the generator, balancing the dynamic coil of the vibrating table; calibration of the stand with checking the frequency and acceleration.
10. Frequency dividers - regulation.
11. Dynamic parameters meter - repair and tuning of the high-frequency unit.
12. Measuring systems like "Viaduct", "Integral" - setting.
13. PK-5003, PK-5005 through passage chambers, control units - temperature control, adjustment, regulation, repair.
14. Semi-automatic classifier - adjustment, repair.
15. Ruler for assembling and adjusting periodic focusing systems, slope gauges - setting.
16. Measuring lines - adjustment, check, repair.
17. Probe manipulators "Zond-A4", "Zond-A5", "EM-680", "EM-6010", "EM-6020" - check, adjustment, repair.
18. Mechanisms with synchronous and monitoring devices - regulation.
19. Electronic microscope, mass spectrometers, thermal cycling units, plasma photometers PFM adjustment.
20. Individual blocks and assemblies that are part of installations or conveyor lines for training and testing the parameters of electrovacuum devices (simulators, reamers, electronic galvanometers, instrumentation amplifiers, low-frequency and high-frequency low power generators, comparators, devices and automation equipment, etc. ) - installation and commissioning.
21. Measuring instruments - adjustment of optics, thread replacement, balancing.
22. Corrective devices and software devices - regulation; electrolytic bath pantograph - adjustment.
23. Semi-automatic contacting and sorting PKRM-2 - setting the kinematic and electronic circuit; regulation of coordination nodes.
24. Devices containing voltage radiation converters, a digital register, an analog-to-digital converter, a unit for automatically changing the conversion limits - installation and configuration.
25. Devices containing scale converters, multipliers, amplitude detectors and analog signal recorders - installation and configuration.
26. Devices of any complexity, IVIS parameters and durability stands, IVIS power and ignition devices, devices for high-speed photography - repair, installation, adjustment.
27. Control panels and devices - installation, adjustment, repair.
28. Tracking systems, special equipment - regulation.
29. Static installations - installation, adjustment.
30. Stand for panoramic measurement of TWT parameters, stands for functional control, functioning blocks - adjustment, repair, installation, commissioning.
31. Bench of service life UNTIS-1 - adjustment of power supply units and temperature setting unit; regulation of pulse duration and generators.
32. Assembly and welding tables of the SSP-2 type - repair, installation and adjustment.
33. Horizontal scanning circuits (tube and semiconductor) for OS and TVS testing - installation and configuration, troubleshooting.
34. Complex schemes and stands for group testing and measuring the parameters of power transformers and chokes, including those for special purposes - manufacturing, tuning and troubleshooting.
35. Schemes and stands for measuring the electrical characteristics of VIS sources - installation and configuration.
36. Scheme of automatic control of the heat chamber, schemes for testing micromodules for special purposes - installation, adjustment, repair.
37. Thermobaric chambers KHTB-0.16 - setting the chamber to elevated temperature (+125 degrees C) and negative temperatures (-60 degrees C), to work at a pace at reduced pressure.
38. Installation for testing semiconductor devices, microcircuits, installations "Zond-1A" and "Zond-A4" - check, adjustment, repair.
39. Installations for measuring high-frequency parameters of semiconductor devices and microcircuits - checking, tuning, repair.
40. Installations for capacitor welding "Wakwell", "Fesd", "MTK-8002", installation for monitoring test parameters of microcircuits based on the meter "EM-640" - repair and adjustment.
41. Installations, stands of test vibration electrodynamic - repair and adjustment.
42. Mechanical impact testing machines - adjustment.
43. Functional nodes on integrated circuits such as a differential amplifier, an analog adder, an integrator, a voltage-to-frequency converter, a register, a comparator of analog signals - installation and configuration.
44. Settings for measuring conversion losses, triode parameters, setting pulse training - repair, tuning.
45. Installations (stands) for testing electrovacuum devices for durability - complex adjustment.
46. Voltage and power amplifiers for various purposes, oscilloscope amplifiers - installation and adjustment.
47. Installation of a test for durability - complex adjustment.
§ 51. Adjuster-installer of test equipment of the 6th category
Job Description. Installation, adjustment and regulation of radio-electronic units of test equipment, computer equipment, test equipment for color kinescopes. Installation, adjustment and operation of test signal sensors (monoscopic installations, slide projectors, film projectors, mono projectors, color stripe generators). Troubleshooting with the help of control tests in programmable pulse generators and voltage sources, counters, registers on a discrete element base and using integrated circuits. Comprehensive adjustment and launch of individual complex blocks in measuring systems. Full check and delivery to the receiver of electrical measuring equipment of any complexity. Calculation of electrical circuits to determine the parameters of radio components of mounted circuits. Control tests of mounted units and radio installations during commissioning.
Must know: methods for detecting faults in radio-electronic units of complex test equipment and computer technology; methods of mounting electronic units, samples of apparatuses and instruments according to sketches and schematic diagrams; calculation of circuits and power supplies; the laws of construction of various assembly and circuit diagrams; purpose and practical application of measuring instruments and instruments; principle of fault detection of electrical parameters and waveforms; forms and parameters of signals in radio-electronic equipment; the impact of interference on the shape and parameters of signals; technical conditions and requirements for the installation of equipment and instruments.
Requires secondary vocational education.
Work examples
1. Analyzers, information-measuring systems installation, adjustment.
2. Power measurement units on the VHF band, functional blocks of computer technology - repair, adjustment.
3. Blocks of breakdown counters - installation, configuration.
4. High-frequency, high-voltage stabilized rectifiers with a voltage of 60,000 V - adjustment.
5. Quantum optical generators of the microwave type - adjustment and repair.
6. Complexes and measuring lines (such as "Integral", Elikon", "Viaduct", etc.) - adjustment, calibration, verification, repair.
7. Modulators of all types - repair and adjustment.
8. Model electric mesh type MSM - setting.
9. Pumping posts with program control - adjustment.
10. Devices for measuring the electrical characteristics of gas-discharge laser pump lamps - installation and adjustment.
11. Devices of the electrostatic system (C), digital type Shch-1413, candle meters, photometers - repair, calibration, regulation.
12. Stand for dynamic testing of pulsed TWT high power - installation, adjustment, repair.
13. Schemes for measuring impulse parameters, for checking the operation of installations - adjustment.
14. Complex schemes and stands for measuring the electrical and light characteristics of VIS sources - installation, adjustment.
15. Complex schemes and benches for group tests and measurements of electrical parameters of OS, fuel assemblies and micromodules of all ratings, including special-purpose ones - tuning, monitoring their operation, repair.
16. Schemes for checking electrical parameters and testing under various environmental conditions - installation, regulation, tuning.
17. Amplifiers of high and low frequency, intermediate frequency (multi-stage), DC amplifiers (multi-stage) - installation, adjustment and regulation.
18. Installations for measuring noise of high-frequency diodes - installation and adjustment.
19. Amplifiers, generators, highly stable power supplies, automatic circuits - installation, regulation, tuning.
20. Amplifying devices with an output power of 3 kW or more - adjustment, repair.
21. Installations for automatic recording of the hysteresis loop, topography of the magnetic field of complex magnetic systems - installation and adjustment.
22. Installations for dynamic and climatic testing of generator pulsed and stroboscopic lamps - repair and adjustment.
23. Installations for measuring static and dynamic parameters of electrovacuum devices, for measuring impulse parameters of semiconductor devices and microcircuits - adjustment, calibration, verification, repair.
24. Installations for thermocompression welding EM-424A., MS-41P2, argon-arc welding type URS-3 - repair and adjustment.
25. Installations potentiometric type U-302, U-309, potentiometers R-307, R2/1; galvanometers; pulse multichannel generators; high-speed oscilloscopes with a bandwidth above 25 MHz; storage oscilloscopes; devices for measuring time and frequency - repair, adjustment, adjustment, installation.
26. Automatic and semi-automatic installations for measuring static and dynamic parameters of reed switches, integrated circuits, microwave semiconductor hybrid circuits - repair and adjustment.
27. Installations for dynamic and climatic testing of reed switches - repair and adjustment.
28. Installations for measuring the noise of reed switches - installation and adjustment.
29. Electron-beam argon purification installations - adjustment.
30. Digital photometers, radiometers, spectroradiometers - installation and adjustment.
31. Centrifuge - repair and adjustment of control circuits.
32. Electrohydrogen furnaces of the type IO570020, AZ6023 - adjustment.
§ 52. Adjuster-installer of test equipment of the 7th category
Job Description. Installation, adjustment and regulation of radio-electronic units of test equipment and computer technology of increased complexity and automation devices on a radio-electronic base with subsequent repair and adjustment. Installation, adjustment, testing, repair and commissioning of industrial automation circuits, telemechanics, communications, contact, relay, electromagnetic, ionic and semiconductor electric drive control circuits. Diagnostics of equipment control systems using special test programs and stands using computer technology. Compilation of test and correction technological programs control and measuring and special technological equipment. Analysis and systematization of failures in the operation of technological equipment.
Must know: methods for detecting faults in radio-electronic units of complex test equipment and computer technology; methods of installation of experimental models of apparatuses and instruments according to sketches and schematic diagrams; laws of construction and calculation of assembly and circuit diagrams; calculation of electrical circuits to determine the parameters of radio components of mounted circuits; ways of compiling and adjusting technological and test programs; organization of a complex of works on adjustment and troubleshooting of devices and systems of computer technology; device and diagnostics of unique measuring and control systems and complexes.
Requires secondary vocational education.
Work examples
1. Blocks of equipment for measuring non-electric quantities by electrical methods (pressure, acceleration, temperature, geometric dimensions meters; flaw detectors, etc.) - installation, adjustment, repair.
2. Blocks of industrial automation, telemechanics and communications (on a radio-electronic basis) - repair, adjustment.
3. Blocks of spreading devices (non-standard) - repair, adjustment.
4. High-frequency generators (sinusoidal, pulse), quantum optical with automatic mode control units - repair, adjustment, frequency adjustment.
5. Complexes of complex automatic and semi-automatic equipment various systems- Troubleshooting, repair, adjustment.
6. Subblocks of algorithms for automatic thermal protection of X-ray tubes, subblocks for processing a television signal (SOTS) - repair and adjustment.
7. Schemes for testing electrovacuum products and monitoring electrical parameters, including those with climatic chambers - installation, repair, adjustment.
8. Schemes and stands for measuring electrical parameters and characteristics of electro-optical devices - setting and monitoring their work, repair.
9. Installations for automated application of the phosphor on the screens of the image intensifier tube - adjustment, repair.
§ 53. Adjuster-installer of test equipment of the 8th category
Job Description. Installation, adjustment, regulation and commissioning of complex control systems, equipment based on microprocessor technology with the performance of all types of restoration and repair work of elements of these systems, programmable controllers, micro- and mini-computers and other computer equipment. Installation and adjustment of equipment for testing color kinescopes using impulse stabilizers and special scanning devices. Installation, adjustment and operation of samples of unique domestic and foreign equipment with automatic control technological processes, with electronic circuits. Participation in the development of non-standard test equipment, installation of blocks and testing them for performance.
Must know: methods for detecting faults in radio-electronic unique domestic and foreign equipment; ways to build control systems based on microprocessor technology, functional and block diagrams micro- and mini-computers; a method for setting up control systems in order to obtain the specified characteristics of devices and instruments of converter technology; programming and repair methods for computer-based equipment.
Requires secondary vocational education.
Work examples
1. Scanners for information display devices, mini- and micro-computer monitors and other control systems - adjustment, installation, regulation.
2. Complex blocks based on LSI - repair and adjustment.
3. Measuring complexes with control computers (such as "Ikomat-110", "Ikomat-115", "Viking", etc.) - adjustment, repair, diagnostics.
4. Control and measuring systems and devices with microprocessor control - installation, adjustment, regulation, diagnostics.
5. Conveyor lines and installations for the manufacture of products of electrovacuum and semiconductor production, equipped with program control and automatic systems for maintaining the specified parameters - repair, adjustment.
6. Schemes of experimental measuring devices and complexes - installation, adjustment, repair.
7. Plants for deposition of thin films of the "Leybold" type, vacuum processing and production of an image intensifier tube photocathode, magnetic deposition of contact layers - repair, adjustment.
Unified Tariff and Qualification Directory of Works and Professions of Workers (ETKS), 2019
Issue No. 48 ETKS
The issue is approved by the Decree of the Ministry of Labor of the Russian Federation of 05.03.2004 N 32
Equipment adjuster in food production
§ 92. Adjuster of equipment in the production of food products of the 3rd category
Job Description. Adjustment, regulation and repair of semi-automatic lines, individual machines and automatic machines under the guidance of an equipment adjuster in the production of food products of higher qualification. Lubrication, stuffing of oil seals, stitching of belts and other similar works.
Must know: rules for the operation of the serviced equipment, regulation, detection and elimination of malfunctions in its operation; technological modes of operation of serviced semi-automatic lines, machines and automatic machines; the procedure for disassembling and assembling serviced machines and equipment.
§ 93. Adjuster of equipment in the production of food products of the 4th category
Job Description. Adjustment, regulation, repair of mechanized and semi-automatic lines, individual machines and automatic machines under the guidance of an equipment adjuster in the production of food products of higher qualification. Checking the technical condition and correct interaction of the units of the serviced equipment, prevention, detection and elimination of technical malfunctions in its operation. Replacement and adjustment of wearing parts and gaskets; assembly and balancing. Equipment testing. Control of the work of semi-automatic lines, individual machines and automatic machines. Adjustment and regulation of components and mechanisms of serviced equipment in the process of operation, participation in various types of repairs, testing and putting it into operation. Lubrication of serviced equipment, stuffing of glands.
Must know: device and design features of serviced equipment, machines and automatic machines; the causes causing malfunctions in the operation of the serviced equipment, methods for their identification and elimination, the procedure for disassembly, assembly and adjustment; rules for the operation and repair of serviced equipment; stock standards for wearing parts; requirements for the quality of adjustment of equipment in the production of food products; rules for using the applied control and measuring tool when performing adjustment work.
§ 94. Adjuster of equipment in the production of food products of the 5th category
Job Description. Adjustment, regulation and repair of mechanized and automated lines, multi-node machines and automatic machines, centrifugal high-speed separators and centrifuges of periodic and continuous action, adjustment and regulation of their units and mechanisms in the process of work. Participation in the performance of various types of repairs of serviced equipment, including overhaul, testing under working load and commissioning.
Must know: arrangement and design features of mechanized and automated lines, multi-node machines and automatic machines, centrifugal high-speed separators and batch and continuous centrifuges; rules for adjustment, interaction and synchronism of their nodes and mechanisms; the causes causing malfunctions in the operation of the serviced equipment, methods for their identification and elimination, the procedure for disassembly, assembly and adjustment; rules for the operation and repair of serviced equipment; device and rules for using the applied control and measuring instruments and tools; rules for sketching simple details.
§ 95. Adjuster of equipment in the production of food products of the 6th category
Job Description. Adjustment, regulation and repair of automated lines or individual high-performance machines for the production of toilet soap, packaged margarine, butter and sugar, for packaging powders, flour, soft cheeses, liquid product bottling lines, production of containers and packaging of pasty products and other similar lines and equipment.
Must know: device, design features of serviced automated lines and high-performance machines; rules for adjustment, repair, operation of serviced equipment; device and rules for using the applied control and measuring instruments.
Requires secondary vocational education.
§ 96. Adjuster of equipment in the production of food products of the 7th category
Job Description. Adjustment, regulation, repair of equipment control system technological lines based on microprocessor technology. Adjustment and diagnostics of line peripheral equipment using test programs and line control system tools. Correction of test and technological programs of serviced equipment. Analysis and systematization of failures in the operation of technological equipment and development of recommendations for their identification and elimination using the programming language used in the automated control system for line equipment.
Must know: device, design features of automated, automatic lines and high-performance machines; rules for maintenance, adjustment, repair of equipment in the production of food products; rules of use and arrangement of instrumentation; methods for correcting test and technological equipment control programs; methods of practical application of the programming language used in the automated control system for equipment of technological lines in the production of food products.
Requires secondary vocational education.